Contents46-3

Vol. 46 No. 3 CONTENTS
Special Issue on Molecular Dynamics Simulation
General Paper

Special Issue on Molecular Dynamics Simulation (Vol.46 No.3)

Foreword
Hiroshi Kitagawa	217

Review paper (Vol.46 No.3)

Definitions of elastic constants

Yoji Shibutani
218

Original Paper (Vol.46 No.3)

Molecular dynamics simulation of Ni crystals under uniaxial deformation

Tomoyuki Yoneda; Moritaka Hida; Akira Sakakibara
228

Atomic simulation of cyclic deformation in very thin wire of nickel

Takayuki Kitamura; Kisaragi Yashiro; Masato Iehara; Ryuichi Ohtani
232

Molecular dynamic study on strength of coincidence grain boundaries

Ken-ichi Saitoh; Hiroshi Kitagawa; Akihiro Nakatani; Shigenobu Ogata
238

Molecular dynamics simulation on the mechanical strength of one component amorphous metal
- decreasing of elastic moduli and strength induced by change of internal structure -

Keiko Nakatani; Hiroshi Kitagawa; Akihiro Nakatani
244

Molecular dynamics simulation of the influence of crystal imperfection on nano machining mechanism

Katsuhiro Maekawa
250

General Paper (Vol.46 No.3)

Technical Note (Vol.46 No.3)

Propagation behavior of long crack in low cycle fatigue regime

Chobin Makabe; Masumi Hiyane; Hideo Kaneshiro
257

Original Paper (Vol.46 No.3)

Analysis of stress intensity factor of chevron notched specimen and measurement of fracture toughness of ceramics

Yoshinori Ebihara; Toshiro Miyoshi; Chiaki Hirai
263

Metallo thermo mechanical simulation of laser quenching process of carbon steel by pulsed YAG laser beam

Kazuyuki Nakasaki; Tatsuo Inoue
268

Flexural strength properties and fracture site morphology of fine ceramics at room and elevated temperatures

Yasuo Ochi; Kohji Haraguchi; Akira Ishii; Shigemi Sasaki
276

Influence of microstructure on the static fatigue crack growth of silicon nitride ceramics

Hiroshi Hohjo; Hirotaka Shibata; Nobuo Kamiya; Akio Otsuka; Takashi Miyata
282

Life prediction rule under creep-fatigue ratcheting conditions of heat-resisting cast alloy, HP-Nb

Toshinori Yokomaku; Masao Kinefuchi; Susumu Terada; Hideki Sugimura; Yasuro Minokata
288

Estimation of low cycle fatigue failure and microscopic change of CFRP
- Observation on AE measurement and microscopic view of CFRP [+-45 degree]₄ -

Katsuhiko Sasaki
295

Application limit of impact end notched flexure test using ramped incident stress wave
- Effects of dimensions of specimen and profile of incident stress wave -

Takayuki Kusaka; Tomoaki Kurokawa; Masaki Hojo; Shojiro Ochiai
302

Influence of water immersion on mechanical properties of glass fabric/epoxy laminates with different fiber surface treatment

Tohru Morii; Nobuo Ikuta; Hiroyuki Hamada
309

Effect of heat cycles on the delamination strength of WC film coated by high-velocity flame spraying

Masahiko Kato; Keijiro Nakasa; Fumiaki Egawa; Masanobu Kamata; Nobuhiko Hara
315

Lecture (Vol.46 No.3)

Design and evaluation frontiers of composite materials
III : Quantitative evaluation of damage in composite materials
- Analysis of evaluation of transverse cracking and stress corrosion cracking -

Shinya Motogi; Hiroyuki Kawata
322

Molecular dynamics simulation of Ni crystals under uniaxial deformation
Tomoyuki Yoneda; Moritaka Hida; Akira Sakakibara	228
Atomic simulation of cyclic deformation in very thin wire of nickel
Takayuki Kitamura; Kisaragi Yashiro; Masato Iehara; Ryuichi Ohtani	232
Molecular dynamic study on strength of coincidence grain boundaries
Ken-ichi Saitoh; Hiroshi Kitagawa; Akihiro Nakatani; Shigenobu Ogata	238
Molecular dynamics simulation on the mechanical strength of one component amorphous metal - decreasing of elastic moduli and strength induced by change of internal structure -
Keiko Nakatani; Hiroshi Kitagawa; Akihiro Nakatani	244
Molecular dynamics simulation of the influence of crystal imperfection on nano machining mechanism
Katsuhiro Maekawa	250

Propagation behavior of long crack in low cycle fatigue regime
Chobin Makabe; Masumi Hiyane; Hideo Kaneshiro	257

Analysis of stress intensity factor of chevron notched specimen and measurement of fracture toughness of ceramics
Yoshinori Ebihara; Toshiro Miyoshi; Chiaki Hirai	263
Metallo thermo mechanical simulation of laser quenching process of carbon steel by pulsed YAG laser beam
Kazuyuki Nakasaki; Tatsuo Inoue	268
Flexural strength properties and fracture site morphology of fine ceramics at room and elevated temperatures
Yasuo Ochi; Kohji Haraguchi; Akira Ishii; Shigemi Sasaki	276
Influence of microstructure on the static fatigue crack growth of silicon nitride ceramics
Hiroshi Hohjo; Hirotaka Shibata; Nobuo Kamiya; Akio Otsuka; Takashi Miyata	282
Life prediction rule under creep-fatigue ratcheting conditions of heat-resisting cast alloy, HP-Nb
Toshinori Yokomaku; Masao Kinefuchi; Susumu Terada; Hideki Sugimura; Yasuro Minokata	288
Estimation of low cycle fatigue failure and microscopic change of CFRP - Observation on AE measurement and microscopic view of CFRP [+-45 degree]₄ -
Katsuhiko Sasaki	295
Application limit of impact end notched flexure test using ramped incident stress wave - Effects of dimensions of specimen and profile of incident stress wave -
Takayuki Kusaka; Tomoaki Kurokawa; Masaki Hojo; Shojiro Ochiai	302
Influence of water immersion on mechanical properties of glass fabric/epoxy laminates with different fiber surface treatment
Tohru Morii; Nobuo Ikuta; Hiroyuki Hamada	309
Effect of heat cycles on the delamination strength of WC film coated by high-velocity flame spraying
Masahiko Kato; Keijiro Nakasa; Fumiaki Egawa; Masanobu Kamata; Nobuhiko Hara	315

Design and evaluation frontiers of composite materials III : Quantitative evaluation of damage in composite materials - Analysis of evaluation of transverse cracking and stress corrosion cracking -
Shinya Motogi; Hiroyuki Kawata	322