Vol. 50 No. 6 CONTENTS
Special Issue on
Engineering Plasticity
Special Issue on Ceramic Material
General Paper

Special Issue on Engineering Plasticity (Vol.50 No.6)

Original Paper (Vol.50 No.6)

Luders Deformation and Strain Ageing of [001] Oriented Fe-30%Cr Alloy Single Crystal

Motohiko KOUSHIMA@and Sei MIURA

559

Effects of Temperature and Loading Type on Inhomogeneous Deformation in Polycrystalline Metals

Katsuhiko YAMAGUCHI, Norio TAKAKURA, Syoji IMATANI and Toshiaki OKAMOTO

566

Plastic Phenomena of Metallic Composite Materials and Powder Sintered Materials

Masaru OMURA and Takahiro YOSHIDA

572

Estimation of Deformation Behavior of Rubber-Blended Glassy Polymers

Wei LU and Yoshihiro TOMITA

578

Numerical Analysis of Deformation of Saturated Clay Based on Cosserat Type Elasto-Viscoplastic Model

Kazuhide SAWADA, Atsushi YASHIMA and Fusao OKA

585

Dependency of the Magnetic Particles' Alignment on Relative Density in Applied Magnetic Field

Hidetoshi KOTERA, Susumu SHIMA and Harunori KITAHARA

593

Three-Dimensional FEM Analysis of Helical Gear Subjected to the Carburized Quenching Process

Manabu FUKUMOTO, Masatoshi YOSHIZAKI, Hideki IMATAKA, Kazuo OKAMURA and Kenji YAMAMOTO

598


Special Issue on Ceramic Material (Vol.50 No.6)

Foreword

N.Miyata

607

Original Paper (Vol.50 No.6)

Evaluation of Nucleation Behavior of Li2O-SiO2 Glass by DTA

Takashi WAKASUGI, Takuya KADOGUCHI and Rikuo OTA

608

Thermoluminescence of Fluoridated Hydroxyapatite Prepared from and -Tricalucium Bis (Orthophosphate)

Kiyoko SAKAMOTO, Kazuno MIZUGUCHI, Shunro YAMAGUCHI and Atsushi NAKAHIRA

613

Analysis of Phase Stability in Cubic Zirconia Solid Solutions by First Principle Molecular Orbital Method

Akihide KUWABARA, Yuichi IKUHARA and Taketo SAKUMA

619

Effects of Porosity and Pore Morphology on Mechanical Properties of Porous Alumina

Tadahiro NISHIKAWA, Atsuhisa NAKASHIMA, Sawao HONDA and Hideo AWAJI

625

Preparation and Properties of ZrO2-Coated BaTiO3 Composite Particles by Sol-Gel Method with Zr-Alkoxide

Takashi HAYASHI, Akihiro TANIMURA, Hiroshi SHINOZAKI, Kazuya TAKANASHI, Hideyuki AOKI and Kyoichi SASAKI

630

Synthesis of Spinel Using Mechano-Chemically Activated Al(OH)3

Haruhisa SHIOMI, Kengo OGAWA, Ken-ichi OKAMOTO, Takeshi SHIONO, Shin-ya OKUMURA, Masataka KAMITANI and Makoto KITAMURA

634


General Paper (Vol.50 No.6)

Original Paper (Vol.50 No.6)

Impact Welding of Aluminum Tube to Stainless Steel Target -Effect of Deformation of Tubular Projectile on Bonding Interface-

Hidefumi DATE

639

Numerical Analysis and Experimental Verification of Laser Quenching for Surface Modification of Ultra-Thin Steel Wire

Atsushi SAKUMA, Yukinobu TOKUNAGA, Takeki YAMANISHI and Makoto KAGAWA

645

Proposal of Delamination Life Prediction Method of Thermal Barrier Coating Layer under Thermal Cycle Condition

Masayuki ARAI, Toshio SAKUMA, Uichi IWATA and Masahiro SATIOH

651

Effects of Prestraining on Low Cycle Fatigue Properties of Low Alloy TRIP Steels

Koh-ichi SUGIMOTO, Sung-Moo SONG, Kazuya INOUE, Mitsuyuki KOBAYASHI and Setsuya MASUDA

657

Lecture (Vol.50 No.6)

Application of Reliability Engineering for Safety Design and Maintenance against Mechanical Structure and Components Y:Application of Reliability Engineering for Preventive Maintenance of Fossil Power Plants and Componerts

Sigeo SAKURAI and Kazunari FUJIYAMA

665